ANSI CAN IAPMO Z1349-2021 pdf free download.Devices for Detection, Monitoring or Control of Plumbing Systems
1 Scope
1.1 General
1.1.1 This standard covers devices for detection, monitoring or control of water supply and
distribution systems in sizes DN 8 to DN 300 (NPS‐1/4 to NPS‐12) for commercial and residential
applications and specifies requirements for materials, performance testing, environmental
limitations, installation, and markings.
1.1.2 Devices for detection, monitoring or control of plumbing systems, hereinafter referred to as
“devices”, covered by this standard govern plumbing systems through features such as:
(a) Automatic shut‐off or electronic alarm notification or isolation of the supply piping when
conditions are detected indicating a leak or equipment malfunction (e.g. automatic water
leak detection and control device).
(b) Detecting the presence of water external to the piping system.
(c) Establishing normal water flow patterns and monitoring for anomalies.
(d) Monitoring of the hydraulic conditions (e.g. water pressure, temperature, or flow) within
the main or branch circuit.
(e) Monitoring of the local environment that may indicate potential for freeze conditions; or
(f) Monitoring of the local environment for moisture that may indicate a leak (e.g. Physical
Water/Moisture Detection Devices).
(g) Monitoring of environmental conditions.
(h) Ongoing analysis of sensor readings or system conditions to ensure monitoring of system
integrity.
(i) Pressure based or other means of micro leak testing for detection of pinhole leaks or
dripping fixtures; or
(j) Provide hardwired or remote access to control a valve (e.g. remotely controlled valves).
Note: Several common terms are used to identify devices covered under this standard a few examples of such terms are Water Leak Detection Device, Automatic Water Leak Detection Device, Leak Detection and Control Device, Adaptive Plumbing System Monitoring and Control Device, and Electronic Plumbing Supply System Integrity and Protection Device.
1.2 Terminology
In this Standard,
(a) “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy to
comply with the Standard.
(b) “should” is used to express a recommendation, but not a requirement.
(c) “may” is used to express an option or something permissible within the scope of the
Standard; and
(d) “can” is used to express a possibility or a capability.
Notes accompanying sections of the Standard do not specify requirements or alternative
requirements; their purpose is to separate explanatory or informative material from the text.
Notes to tables and figures are considered part of the table or figure and can be written as
requirements.
1.3 Units of Measurement
SI units are the primary units of record in global commerce. In this Standard, the inch/pound
units are shown in parentheses. The values stated in each measurement system are equivalent
in application, but each unit system is to be used independently. All references to gallons are to
U.S. gallons.
1.4 Amendments
Proposals for amendments to this Standard will be processed in accordance with the standards‐
writing procedures of IAPMO.
Metering Device – A device that measures water flow through a water pipe, that tracks volume of water used. A metering device may send a signal when pre‐set conditions are met. Micro Leak – A water leak having a flow rate of 14 ml/h (0.5 oz/h) or less. Monitoring – Ongoing analysis of sensor readings including pressure, temperature (ambient or water), flow rate or system conditions. Note: “Smart devices” typically provide the information gathered from sensor readings to the user of the system and an integrated or remote CPU for monitoring, analysis, and feedback. Non‐Invasive Monitoring Device – Measures the system conditions (e.g. water temperature, and flow) without penetrating through the exterior of the system or encountering the internal water. Physical Water/Moisture Detection Device – Senses water or moisture in specific locations through contact and sends a signal when activated to a receiving device. Note 1: Once the receiving device gets a signal, it typically takes an action such as alerting maintenance, triggering a noise, system alarm or silent alarm, or when attached to an automatic control valve turning‐ off the water supply. Note 2: Detection devices can use an electronic circuit that is normally open but becomes closed in the presence of or through contact with water.
